Just How to Replace a Tub
Just How to Replace a Tub
Blog Article
We've discovered this great article about Tools You Need to Install a New Bathtub below on the web and accepted it made perfect sense to share it with you on this page.
Setting up a tub isn't precisely rocket science, but it does require solid plumbing, carpentry, and sometimes, tiling abilities. Changing an old tub with a new one is likewise a moderately difficult project. If the old bathtub is conveniently obtainable, the job can move quickly; if you have to open a wall surface to get rid of the old bathtub as well as position the new bath tub, the job is a lot harder. In either situation, the task is within a residence handyman's abilities, although you will need an assistant to leave the old tub as well as embeded in the new one. Make sure you have actually qualified on your own for the task and fit attempting it. As opposed to employing a professional to take control of a halfway-completed project, it is far better to think about using one before you start. Possibilities are you might need a professional plumber to make tube links.
This write-up will certainly help you mount a brand-new tub in your bathroom if you have actually already acquired a brand-new tub as well as don't require to alter the arrangement of your previous water pipelines.
Your tools and product checklist need to make up the following:
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you ought to do is disconnect the supply of water. After doing so, activate the taps to drain pipes any type of water remaining in the system. The procedure of removing the existing faucets can be rather bothersome because of the limited gain access to that is frequently the situation.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the faucets. Have a cloth prepared for the continuing to be water that will originate from the pipes. When the supply pipelines have been eliminated, use the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from turning during this procedure. Once the taps have actually been removed, the holes in the bath/basin will need to be cleaned of any type of old securing substance.
Before carrying on to fit the brand-new taps, compare the pipe links on the old faucets to the new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will need a plastic port to stop damage to the thread. One end of the port fits on the plastic tail of the faucet and also the other end offers a connection to the current supply pipelines.
If you require to fit a monobloc, then you will need minimizing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, position the faucet in the mounting hole in the bath/basin making sure that the washing machines remain in area in between the tap and the sink. Secure the tap in position with the maker given backnut. As soon as the faucet is firmly in position, the supply pipes can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with normal tap connectors. The former type should be connected to the tap ends first, tightening only by hand. The supply pipes can later be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Mounting the Bath tub
Utilizing the two wooden boards under its feet, place the bathtub in the required setting. The wood boards are practical in evenly spreading the weight of the tub over the area of the boards rather than focusing all the weight onto four small points.
The next objective is to make certain that the bath tub is leveled all round. This can be attained by inspecting the spirit level as well as readjusting the feet on the bath tub up until the spirit level reads level.
To mount faucets, fit all-time low of the furthest flexible faucet port to the suitable supply pipe by making a compression join; after that do the exact same for the other tap.
Activate the water system and check all joints and also brand-new pipework for leaks and tighten them if essential. Fill up the tub and additionally inspect the overflow outlet and the regular outlet for leaks.
Ultimately, repair the bathroom paneling as explained in the producer's instruction manual. Tiling and also sealing around the bathtub needs to wait up until the bathtub has actually been utilized at least when as this will resolve it into its final placement.
Preparing for the Setup
Firstly, the sustaining framework provided with the bathroom should be fitted (if called for) according to the producer's guidelines. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is essential to see to it that if the tap includes a plastic washer, it is fitted in between the bath as well as the taps. On a plastic bathroom, it is also practical to fit a supporting plate under the taps device to avoid pressure on the tub.
Fit the adaptable tap adapters to the bottom of the two faucets using 2 nuts as well as olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Make certain you make use of all of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom should now prepare to be fitted in its final placement.
Tiling Around the Bathtub
In the location where the bathroom meets the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is important as the installation can relocate enough to break an inflexible seal, causing the water to permeate the wall surface between the bath and the tiling, resulting in issues with wetness and also possible leaks to the ceiling below.
You can select from a range of coloured sealers to blend in your components as well as installations. They are offered in tubes as well as cartridges, as well as can securing voids approximately a size of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with twists of soaked newspaper or soft rope. Remember to always fill the bathtub with water before sealing, to allow for the movement experienced when the tub is in use. The sealant can crack fairly early if you do not take into consideration this motion prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also easily available on the marketplace. It is recommended to fit the ceramic tiles using waterproof or water-proof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
As an avid person who reads about How to Install a Bathtub Yourself, I imagined sharing that segment was worthwhile. Are you aware of someone else who is interested by the topic? Please feel free to promote it. We appreciate reading our article about How to Install a Bathtub Yourself.
Apply Now Report this page